Scientific objectives and payloads of Tianwen-1, China’s first Mars exploration mission

This paper describes the scientific objectives and payloads of Tianwen-1, China’s first exploration mission to Mars. An orbiter, carrying a lander and a rover, lifted-off in July 2020 for a journey to Mars where it should arrive in February 2021. A suite of 13 scientific payloads, for in-situ and remote sensing, autonomously commanded by integrated payload controllers and mounted on the orbiter and the rover will study the magnetosphere and ionosphere of Mars and the relation with the solar wind, the atmosphere, surface and subsurface of the planet, looking at the topography, composition and structure and in particular for subsurface ice. The mission will also investigate Mars climate history. It is expected that Tianwen-1 will contribute significantly to advance our scientific knowledge of Mars.     

Simulation and Analysis of Electromagnetic Force in Laser Melting Deposition by Electromagnetic Impact

Magnetic field was introduced in laser melting deposition to reduce the pores in workpieces.Finite 3-D model of the coil-deposition layer-substrate was established.Simulation results show that the electromagnetic force in deposition layer mainly concentrates in the projection area of the coil.Axial electromagnetic force shows repulsion in one cycle.The experimental results indicate that the magnetic field is beneficial for grain refinement,microhardness increasement and decline of quantities and average sizes of pores.     

Interference torque of a three-floated gyroscope with gas-lubricated bearings subject to a sudden change of the specific force

A numerical study is carried out to investigate the influence of a sudden change of the specific force on a three-floated gyroscope with a rotor supported on gas-lubricated bearings.The interference torque is calculated to evaluate the influence by modeling the transient behavior of the rotor-bearing system. In combination with dynamic equations of the rotor displacement,the Reynolds equation is solved on the surface of spiral-grooved conical bearings. It is assumed that a steady state has been obtained with a constant specific force, and then the specific force is suddenly changed and maintained constant after that. Responses of the sudden change are obtained by solving the equations. Numerical results show that the direction of the sudden change of the specific force is the main factor which influences the interference torque curve. With a sudden change along the input direction, the interference torque fluctuation has a constant frequency and a decreasing amplitude. With a sudden change along the output direction, the interference torque fluctuates in a small range. With a sudden change along the spin direction, the change of the interference torque combines a fluctuation and a gradually-changing quasi-equilibrium value. This study provides a supplement to the steady-state error model of the three-floated gyroscope.     

第23太阳活动周太阳极紫外辐射与磁暴相关性分析

统计第23个太阳活动周内中等及以上强度（Dst_min<-50nT）的磁暴事件，线性拟合分析磁暴主相DDst_min和达到DDst_min前一个表征太阳极紫外辐射强度的F_10.7之间的相关性.结果表明:随着太阳极紫外辐射增强，DDst_min<-50nT的磁暴出现的总数增多，在弱、中等和强太阳极紫外辐射条件下，其数量分别为56，84和85；随着太阳极紫外辐射增强，强磁暴（-200nT ≤ Dst_min<-100nT）和大磁暴（Dst_min<-200nT）发生的数量和相对发生率呈增长趋势，尤其是大磁暴数目（1，4，12）和相对发生率（1.79%，4.76%，14.12%）明显呈增长趋势；大磁暴（|Dst_min|）与太阳极紫外辐射（F_10.7）之间存在中度正相关关系，其相关系数为0.532，并且主要体现在大磁暴（|Dst_min|）与强太阳极紫外辐射（F_10.7）之间的中度正相关性，其相关系数为0.582.大磁暴与强太阳极紫外辐射之间的相关性可为空间天气预报提供参考依据.      

基于幅频响应特性的半球谐振子频率裂解与固有刚度轴方位角测定方法

半球谐振子频率裂解与固有刚度轴方位角是影响陀螺性能指标的核心因素。提出了一种基于幅频响应特性的半球谐振子频率裂解与固有刚度轴方位角测定方法，采用压电激振台扫频激振，多普勒激光测振仪检测谐振子的幅频响应特性，通过幅频响应特性曲线分析实现频率裂解与固有刚度轴方位角的测定。对该方法进行了理论分析，搭建了实验装置，并对半球谐振子进行了测试，结果表明：该方法频率裂解测量精度优于0.01Hz，固有频率主轴方位角确定精度优于±1.17°，具有良好的可行性，在半球谐振陀螺研制方面具有良好的参考意义。     

多种工质下螺旋波等离子体源波场结构数值模拟

针对螺旋波等离子体放电机理，开展了多种工质条件下的螺旋波放电等离子体内波场结构数值模拟研究。计算发现:氦气等离子体的Er分量在径向边界处的峰值更为突出，有利于等离子体在径向的输运，波电场径向分量决定了电流密度径向分量在内部的表现。在0.266 Pa和1.064 Pa两种气体压强条件下，通过波场结构验证了气压对于波阻尼影响的结论。波场结构是螺旋波在等离子体内传播以及能量沉积的微观体现，研究螺旋波波场结构是揭示其高电离效率的重要途径。初步探索了功率耦合机制，为实验系统优化及实验方案设定奠定理论基础。     

基于拉格朗日方法的通气云状空泡三维非定常脱落特性研究

采用均相流模型并结合FBM湍流模型,对绕轴对称回转体通气云状空泡流动特性进行了三维数值模拟,基于实验结果对数值方法进行验证,同时利用基于拉格朗日体系的有限时间李雅普诺夫指数(FTLE)、拉格朗日拟序结构(LCS)和粒子追踪方法分析了其三维非定常脱落特性。研究结果表明:纵截面上空泡覆盖区域的拉格朗日拟序结构整体呈椭球状分布,内部为不规律的复杂拟序结构;不同横截面上拟序结构分布存在很大差异。空泡内部的非对称流动结构和周向流动导致空泡呈现很强的三维运动特性。反向射流在周向上推进的不同步性,是造成空泡呈现不规则断裂和大尺度U型空泡团脱落的主要原因。     

永磁同步电机最优滑模控制

为了减少永磁同步电机调速中的动态误差,提出了一种积分性能最优的滑模控制方法。该方法以滑模控制中的动态误差为性能指标,在此基础上建立最优切换函数,并采用最优控制理论对滑模控制器进行设计。用该方法设计的滑模控制系统,通过滑模面斜率的连续变化,能够加速系统状态变量到达滑模面的过程,极大地提高对参数摄动和外部干扰的鲁棒性。仿真结果表明,该时变滑模面控制方法使系统具有无超调、快速、稳定等优点,提高了系统的鲁棒性。     

四相横向磁通永磁电机的三电平滞环电流控制

以新型四相横向磁通永磁电机为研究对象,利用MATLAB/Simulink软件平台以及Simpower System工具箱,对闭环控制系统进行了研究。在传统双闭环调速控制基础上,为滞环电流控制环引入零电平,将滞环分为上滞环和下滞环。综合考虑开关频率与电流THD确定合适的滞环环宽,并根据偏差电流值与滞环环宽比较值得到逆变器控制信号。通过仿真得到各种工况下的电机运行数据,说明该控制方法能够对四相横向磁通永磁电机进行有效控制。